Installing ULTRIX-11 V3.1(1)

Fred N. van Kempen, Senior Consultant
MicroWalt Corporation, Palo Alto, CA

Email: fred.van.kempen@microwalt.nl



INTRO
First of all, make _sure_ your hardware is in working order.  It is
quite hard to debug misbehaving installation procedures if you run
it on faulty hardware !

I am doing this test load on the following machine:

- MicroPDP-11/53, 512KB onboard RAM, 2 SLU's (console and aux)
- RQDX3 disk controller, with internal RD31 drive (20MB)
- TQK50 tape controller, with internal TK50 drive

I just did a new low-level format on the hard drive, so it's very,
very empty.  The system will of course complain about not having a
bootable drive.


SUPPORTED SYSTEMS
Although in theory ULTRIX-11 should work on all PDP-11 processors,
certain design and capacity issues make it (nearly?) impossible to
get it to run on certain processors.

The official list of supported processors is:

        23, 23+, 24, 34, 40, 44, 45, 55, 60, 70, 73, 83, 84

I have personally tested it on a 23+, 53 and 83.  I know it runs
fine on the 73.  The smaller machines (34, 40 etc) should work
akin to the 23, meaning using overlays and be very tight on RAM
for the drivers.  TCP/IP is a biiiiig load for those systems!

For now, you can only load ULTRIX-11 onto your system with a
working tape drive... TK50, magtape, etc.  My distribution kit
was made for the TK50, but future releases will have support for
all the available (and usable... no TU58 support, sorry :) tape
drives/controllers.

Also, note that the next release of this kit will fully support
the (very much enhanced) VTserver 2.0 system, which will allow
you to download the distribution tape file (currently a tar file,
but my new TDF format soon), tell VTserver about it, and install
the kit off the VT server over serial line.  Slow, but it works.

(and HEY... the TK50 isn't much faster... trust me ;)

Don't be anal about your systems... ULTRIX-11 is a fairly hefty
version of UNIX for the PDP-11... I'd say that with 2.11BSD, it
is the most bloated one you can get.  Don't try to run it on
systems which have little hardware (memory, disk, etc).. it's
not going to work.

According to the kernel sources, the very minimum amount of RAM
to actually _boot_ (i.e. loading /boot) is 192KB.  If boot detects
less RAM, it aborts, because the kernel needs to live in that
{falafel:~} $ cat setup.txt
    Installing ULTRIX-11 V3.1(1)

Fred N. van Kempen, Senior Consultant
MicroWalt Corporation, Palo Alto, CA

Email: fred.van.kempen@microwalt.nl



INTRO
First of all, make _sure_ your hardware is in working order.  It is
quite hard to debug misbehaving installation procedures if you run
it on faulty hardware !

I am doing this test load on the following machine:

- MicroPDP-11/53, 512KB onboard RAM, 2 SLU's (console and aux)
- RQDX3 disk controller, with internal RD31 drive (20MB)
- TQK50 tape controller, with internal TK50 drive

I just did a new low-level format on the hard drive, so it's very,
very empty.  The system will of course complain about not having a
bootable drive.


SUPPORTED SYSTEMS
Although in theory ULTRIX-11 should work on all PDP-11 processors,
certain design and capacity issues make it (nearly?) impossible to
get it to run on certain processors.

The official list of supported processors is:

        23, 23+, 24, 34, 40, 44, 45, 55, 60, 70, 73, 83, 84

I have personally tested it on a 23+, 53 and 83.  I know it runs
fine on the 73.  The smaller machines (34, 40 etc) should work
akin to the 23, meaning using overlays and be very tight on RAM
for the drivers.  TCP/IP is a biiiiig load for those systems!

For now, you can only load ULTRIX-11 onto your system with a
working tape drive... TK50, magtape, etc.  My distribution kit
was made for the TK50, but future releases will have support for
all the available (and usable... no TU58 support, sorry :) tape
drives/controllers.

Also, note that the next release of this kit will fully support
the (very much enhanced) VTserver 2.0 system, which will allow
you to download the distribution tape file (currently a tar file,
but my new TDF format soon), tell VTserver about it, and install
the kit off the VT server over serial line.  Slow, but it works.

(and HEY... the TK50 isn't much faster... trust me ;)

Don't be anal about your systems... ULTRIX-11 is a fairly hefty
version of UNIX for the PDP-11... I'd say that with 2.11BSD, it
is the most bloated one you can get.  Don't try to run it on
systems which have little hardware (memory, disk, etc).. it's
not going to work.

According to the kernel sources, the very minimum amount of RAM
to actually _boot_ (i.e. loading /boot) is 192KB.  If boot detects
less RAM, it aborts, because the kernel needs to live in that
space.  So, with 192KB for the kernel, you need at least 248KB
of RAM to get a shell going.  And therefore, we state (listen up,
y'all!) that:

  ULTRIX-11 V3.1(1) AND UP NEED 248KB OF RAM AT THE VERY LEAST !

So there.  If you have a PDP-11/03 with 56KB of memory and a
TU58, then look elsewhere... RT11 is nice, and so is Xinu.


BOOT THE SYSTEM
Let's start her up:

------------------------------------------------------------------
9 8 7 6 5 4 3 2 1 


KDJ11-D/S   E.01
No bootable devices found
Boot in progress - Type CTRL C to exit <CTRL-C typed here>

Commands are Help, Boot, List, Map, Test and Wrap.
Type a command then press the RETURN key:
------------------------------------------------------------------

This looks good so far.  No complaints about failing hardware other
than the missing bootable device.

Insert the ULTRIX-11 V3.1(1) load kit into the TK50 drive, and type

        B MU0

to start it up.  The system will respond with:

-----------------------------------------------------------------
MU0


Sizing Memory...  

To list options, type help then press <RETURN>

Boot: 
-----------------------------------------------------------------

Welcome to Ultrix!  You have just started up the primary boot
program of the Ultrix system.  We have to load the system install
program from the tape, so type:

        tk(0,2)

and the tape will spin again.  The above means "load file number
2 from the tape in tape drive zero".  That is the "sdload" (System
Disk Load) program, which greets us with:

----------------------------------------------------------------
       ****** ULTRIX-11 System Disk Load Program ******

This program loads the base ULTRIX-11 system from the distribution
media onto the system disk, then bootstraps the system disk. After
booting, the setup program begins the initial setup dialogue.

Before loading can begin, you need to answer some questions about
your system's configuration. Enter your answer, using only lowercase
characters, then press <RETURN>. If you need help answering any of
the questions, enter a ? then press <RETURN>.

To correct typing mistakes press the <DELETE> key to erase a single
character or <CTRL/U> to erase the entire line.

Press <RETURN> to continue:


                  ****** WARNING ******

Installing the ULTRIX-11 software will overwrite your system disk.
In addition, the ULTRIX-11 V3.0 file system is not compatible with
the file systems used by previous ULTRIX-11 releases or any other
software systems. Existing user disks must be converted to the new
1K block file system.

DO NOT PROCEED UNTIL YOU HAVE READ INSTALLATION GUIDE SECTION 1.7

Proceed with the installation <y or n> ? y

Target processor is an 11/53 <y or n> ? y

CURRENT CPU = 11/53, TARGET CPU = 11/53

System disk type <? for help> ? ?

Please enter the generic name of your system disk.
Select from the following list of supported disks:

rd31 rd32 rd51 rd52 rd53 rd54 rl01 rl02 
rk06 rk07 rp02 rp03 rp04 rp05 rp06 rm02 
rm03 rm05 ra60 ra80 ra81 rc25 

System disk type <? for help> ? rd31


                ****** CAUTION ******

You must scan MSCP disks for bad blocks, type ?<RETURN> for help!

Scan system disk(s) for bad blocks <y or n> ? y

****** SCANNING SYSTEM DISK(s) FOR BAD BLOCKS ******
-----------------------------------------------------------------

The SDLOAD program halts, and in turn loads the "rabads" program
from the tape, which checks the drive(s) for bad sectors it needs
to re-map to good sectors:

-----------------------------------------------------------------
ULTRIX-11 MSCP Disk Initialization Program

Disk type < ra60 ra80 ra81 rx33 rx50 rd31 rd32 rd51 rd52 rd53 rd54 rc25
>: rd31

Unit number < 0-3 >: 0

Starting block number < 0 >: 0

Number of blocks to check < 41560 >: 

READING...


41560 blocks checked
0 bad blocks found
0 bad blocks replaced

Exit called

-----------------------------------------------------------------

We are now thrown back into SDLOAD, which tells us that the bad block
scan has finished, and that it is now ready to create an empty file
system on that drive:

-----------------------------------------------------------------
****** BAD BLOCK SCAN COMPLETE ******


****** MAKING EMPTY (ROOT) FILE SYSTEM ******

File system size: 4850
Disk type: rd31
Processor type: 53
File system name: root
Volume name: sd_rd0
File system: rd(0,0)
isize = 3104
m/n = 1 72
Exit called

****** EMPTY FILE SYSTEM COMPLETED ******
--------------------------------------------------------------

Now that we have a file system to work with, we can load (restore)
a standard root file system from the tape.  SDLOAD will call the
"restor" program to do just that:

---------------------------------------------------------------
****** RESTORING (ROOT) ONTO SYSTEM DISK ******

Input: tk(0,0)root
Disk: rd(0,0)

End of dump media

****** FILE SYSTEM RESTORE COMPLETE ******
---------------------------------------------------------------

SDLOAD will now call the "icheck" program to check the newly restord
file system for any errors.  This should not be needed, but hey, you
never know....

----------------------------------------------------------------
****** CHECKING (ROOT) FILE SYSTEM ******

File: rd(0,0)
Salvage free list <y or n> ? n
rd(0,0):
files 305 (r=280,d=17,b=1,c=7,p=0,l=0)
used 3389 (i=182,ii=0,iii=0,d=3207)
free 1265
missing 0

****** FILE SYSTEM CHECK COMPLETE ******
------------------------------------------------------------------

Well, all seems to be well.  It continues with creating an empty
file system for the /usr file system:

-----------------------------------------------------------------
****** MAKING EMPTY (USR) FILE SYSTEM ******

File system size: 14364
Disk type: rd31
Processor type: 53
File system name: /usr
Volume name: sd_rd0
File system: rd(0,12800)
isize = 9184
m/n = 1 72
Exit called

****** EMPTY FILE SYSTEM COMPLETED ******
------------------------------------------------------------------

restore data to it from tape:

------------------------------------------------------------------
****** RESTORING (USR) ONTO SYSTEM DISK ******

Input: tk(0,0)usr
Disk: rd(0,12800)

End of dump media

****** FILE SYSTEM RESTORE COMPLETE ******
------------------------------------------------------------------

and of course will go and check this one, too:

------------------------------------------------------------------
****** CHECKING (USR) FILE SYSTEM ******

File: rd(0,12800)
Salvage free list <y or n> ? n
rd(0,12800):
files 619 (r=570,d=49,b=0,c=0,p=0,l=0)
used 4824 (i=228,ii=1,iii=0,d=4594)
free 8965
missing 0

****** FILE SYSTEM CHECK COMPLETE ******
------------------------------------------------------------------

Now that we have the basic system set up, it's time to install the
secondary bootstrap for the selected device (RQDX MSCP) and rebooting
the newly installed system:

--------------------------------------------------------------------
****** COPYING BOOT TO SYSTEM DISK BLOCK ZERO ******


****** BLOCK ZERO BOOT LOADED ******


****** BOOTING ULTRIX-11 SYSTEM TO SINGLE-USER MODE ******

Sizing Memory...  

Boot: rd(0,0)unix    (CTRL/C will abort auto-boot)

rd(0,0)unix:
14784+17024+8192+8000+8064+8000+8064+8128+8000+7808+7936+7936+7680+
7360+1344

ULTRIX-11 Kernel V3.1

realmem = 524288
buffers = 25600
clists  = 1600
usermem = 365120
maxumem = 212992
erase = delete, kill = ^U, intr = ^C


            ****** ULTRIX-11 Setup Program ******


This program performs operating system setup functions during
installation and normal system operation. Setup operates in one
of three possible modes (phases), depending on the current state
of the system. The three modes are:

 Phase 1: Initial setup -- prepares system for first sysgen.
 Phase 2: Final setup -- completes the system setup.
 Phase 3: Change setup -- handles system setup changes.

The program will ask several setup questions. Enter your answer
to each question, using lowercase characters, then press <RETURN>.

The questions include helpful hints enclosed in angle brackets < >
and/or parenthesis ( ). If you need additional help answering any
question, enter a ? or the word help then press <RETURN>.

You can correct typing mistakes by pressing the <DELETE> key to
erase a single character or <CTRL/U> to erase the entire line.
You can interrupt the setup program by typing <CTRL/C>. This
allows you to abort the setup process or restart it.

Press <RETURN> to continue: 
--------------------------------------------------------------------

Heh.  Welcome back!  This is fun, isn't it?  We're now running the
Ultrix system, and we are going to set it up.

First, answer the questions:

--------------------------------------------------------------------
Is the console terminal a CRT (video terminal) <y or n> ? y

PLEASE CONFIRM: console is a VIDEO terminal <y or n> ? y

****** READING SETUP DATA FROM setup.info FILE ******

SETUP PHASE      = 1 (Initial Setup)
LOAD DEVICE TYPE = TK50 UNIT 0
SYSTEM DISK TYPE = RD31
CURRENT CPU TYPE = 11/53
TARGET  CPU TYPE = 11/53

Is the above information correct <y or n> ? y

****** ENTERING SETUP PHASE 1 ******

Is this the target processor (? for help) <y or n> ? y

PLEASE CONFIRM: on the target processor <y or n> ? y

Terminal type for CONSOLE terminal < vt100 > ? 

What is your AC power line frequency in hertz < 50 or 60 > ? 50

PLEASE CONFIRM: AC line frequency is 50 hertz <y or n> ? y

What is your local time zone < hours west/behind GMT > ? 0

PLEASE CONFIRM: time zone is 0 hours west/behind GMT <y or n> ? y

Does your local area use daylight savings time <y or n> ? y

PLEASE CONFIRM: daylight savings time in use <y or n> ? y

Choose the Geographic Area for the daylight savings time from  the table
below

                Geographic Area Selection
                --------------- ---------
                USA                1
                Australia          2
                Western Europe     3
                Central Europe     4
                Eastern Europe     5

Enter the selection number <1> 3

PLEASE CONFIRM:  Geographic area is 3 <y or n> ?y

Please enter the current date/time < yymmddhhmm.ss > ? 0103062237

Fri Mar  6 22:37:00 GMT 1970

PLEASE CONFIRM: date/time correct <y or n> ? y

****** SELECTING SPLIT I/D COMMANDS (/bin) ******

****** ZEROING THE ERROR LOG FILE ******

****** MAKING SYSTEM DISK(s) SPECIAL FILES ******

****** MAKING MAGTAPE SPECIAL FILES ******

****** SELECTING SPLIT I/D COMMANDS (/usr/bin, lib, ucb) ******

****** ULTRIX-11 Setup Phase 1 Completed ******

You can now run the sysgen program and generate a new ULTRIX-11
kernel to match your system's hardware configuration. Return to
the Installation Guide for instructions.


# 
---------------------------------------------------------------

Ohyeah.  Did you notice how the "date" command did not work? The
system thinks it's 1970 now.  Ahwell, we'll fix that later, and
actually fix the code in the next release of this kit.

We now type:

        sync
        sync
        sync

and reboot the machine:

------------------------------------------------------------
9 8 7 6 5 4 3 2 1 

DU0


Sizing Memory...  

Boot: rd(0,0)unix    (CTRL/C will abort auto-boot)

rd(0,0)unix: 37534+54720+8128+8000+7488+5312+3648

ULTRIX-11 Kernel V3.1

realmem = 524288
buffers = 76800
clists  = 2080
usermem = 285568
maxumem = 285568
erase = delete, kill = ^U, intr = ^C


            ****** ULTRIX-11 Setup Program ******


This program performs operating system setup functions during
installation and normal system operation. Setup operates in one
of three possible modes (phases), depending on the current state
of the system. The three modes are:

 Phase 1: Initial setup -- prepares system for first sysgen.
 Phase 2: Final setup -- completes the system setup.
 Phase 3: Change setup -- handles system setup changes.

The program will ask several setup questions. Enter your answer
to each question, using lowercase characters, then press <RETURN>.

The questions include helpful hints enclosed in angle brackets < >
and/or parenthesis ( ). If you need additional help answering any
question, enter a ? or the word help then press <RETURN>.

You can correct typing mistakes by pressing the <DELETE> key to
erase a single character or <CTRL/U> to erase the entire line.
You can interrupt the setup program by typing <CTRL/C>. This
allows you to abort the setup process or restart it.

Press <RETURN> to continue: 

Is the console terminal a CRT (video terminal) <y or n> ? y

PLEASE CONFIRM: console is a VIDEO terminal <y or n> ? y

****** READING SETUP DATA FROM setup.info FILE ******

SETUP PHASE      = 2 (Final Setup)
LOAD DEVICE TYPE = TK50 UNIT 0
SYSTEM DISK TYPE = RD31
CURRENT CPU TYPE = 11/53
TARGET  CPU TYPE = 11/53

Is the above information correct <y or n> ? y

****** ENTERING SETUP PHASE 2 ******

Please enter the current date/time < yymmddhhmm.ss > ? 0003062257

Sat Mar  7 22:57:00 GMT 1970

PLEASE CONFIRM: date/time correct <y or n> ? y

DIGITAL recommends you add the following information to the
configuration work sheet located in the Installation Guide.
This work sheet will be helpful if you need to remake your
device special files using setup phase 3.

The program will pause periodically to allow time for you
to record the configuration information.

Press <RETURN> to continue: 

****** DETERMINING SYSTEM'S DISK CONFIGURATION ******

ULTRIX-11 System's Disk Configuration:

X = disk not configured, NED = disk configured but not present.

Disk    Cntlr  System  Unit  Unit  Unit  Unit  Unit  Unit  Unit  Unit
Cntlr   #      Disk    0     1     2     3     4     5     6     7
-----   -----  ------  ----  ----  ----  ----  ----  ----  ----  ----
RQDX3   0      UNIT 0  RD31  X     X     X     X     X     X     X     

Press <RETURN> to continue: 

****** MAKING DISK SPECIAL FILES ******

****** DETERMINING SYSTEM'S TAPE CONFIGURATION ******

Magtape Controller       # Units
------------------       -------
TK50/TU81                1

Press <RETURN> to continue: 

****** MAKING MAGTAPE SPECIAL FILES ******

****** DETERMINING SYSTEM'S COMMUNICATIONS DEVICE CONFIGURATION ******

Device  # Units  Lines/Unit
------  -------  ----------
NO COMMUNICATIONS DEVICES FOUND!

****** DETERMINING NUMBER OF PSEUDO TTYS ******

Number of PTTYs = 4

Press <RETURN> to continue: 

****** DETERMINING NUMBER OF MAUS SEGMENTS ******

Number of MAUS segments = 4

****** MAKING MAUS SPECIAL FILES ******

****** CREATING /etc/ttys and /etc/ttytype FILES ******

Terminal type for CONSOLE terminal < vt100 > ? 

****** NAMING YOUR ULTRIX-11 SYSTEM ******

Please enter your system's hostname <? for help> ? kwek

PLEASE CONFIRM: hostname is `kwek' <y or n> ? y

Set up line printer spooler and printer ports <y or n> ? n

Set up user file systems <y or n> ? n

Load/unload optional software <y or n> ? y


ULTRIX-11 SETUP: Optional Software Load Program.

For instructions type `help', then press <RETURN>.

Command <help free rxunit rxdir list load unload exit>: list

Item    # K- On-  Load  Item
Name    Byte Disk Dir.  Description
------- ---- ---- ----  ----------------------------------------------
dict     210   no /USR  Spell dictionary and hash lists
                        (Not needed unless remaking spell dictionary)
docprep  980   no /USR  Document prepration software: nroff troff roff
                        refer (+ dict/papers) tbl eqn fonts macros
f77      350   no /USR  Fortran 77 programs and libraries
                        (f77, ratfor, structure and beautify)
games    300   no /USR  Games (Programmer's Manual, Vol. 1, Section 6)
learn    860   no /USR  Learn scripts (Computer Aided Instruction)
libsa     60   no /USR  Library for building stand-alone programs
manuals 2100   no /USR  On-line ULTRIX-11 Programmer's Manual, Volume 1
                        (for use with man(1) and catman(8) commands)
orphans  360   no /USR  ORPHAN files: old versions of some software
                        (refer to /usr/orphan/README for help)
pascal   250   no /USR  PASCAL interpreter, executer, and profiler
                        (University of California at Berkeley 2.9 BSD)
plot     185   no /USR  Plot libraries (graphics filters and programs)
saprog   125  yes ROOT  Stand-alone programs in /sas directory: scat
                        copy icheck mkfs restor bads rabads dskinit
sccs     300   no /USR  Source Code Control System
spell    175   no /USR  Spelling checker and associated programs
                        (programs to rebuild hlists from dictionary)
sysgen   890  yes /USR  System generation programs and files
tcpip    410   no /USR  TCP/IP ethernet networking software
                        (for local area network over an ethernet)
usat     205   no /USR  ULTRIX-11 System Acceptance Test
                        (verifies the system is installed and working)
usep     400   no /USR  User-mode System Exerciser Package
                        (verifes system hardware working properly)
userdev  140   no /USR  User written device driver sources and
documentation
uucp     340   no /USR  UUCP (unix to unix copy)
                        (connect to other systems via phone or hardwire)

Command <help free rxunit rxdir list load unload exit>: load

Please enter a list of items to LOAD (? for help).

List: dict docprep f77 games learn libsa manuals orphans pascal plot
saprog sccs
 spell tcpip usat usep userdev uucp

Load any items with symbolic links (? for help) <y or n> ? n

Make sure the distribution tape (or TK50 cartridge) is
mounted in unit zero and the unit is on-line and ready.

Press <RETURN> to continue:

****** LOADING (dict) ******

****** LOADING (docprep) ******

****** LOADING (f77) ******

****** LOADING (games) ******

****** LOADING (learn) ******

****** LOADING (libsa) ******

****** LOADING (manuals) ******

****** LOADING (orphans) ******

****** LOADING (pascal) ******

****** LOADING (plot) ******

****** UNLOADING (saprog) ******

****** LOADING (saprog) ******

****** LOADING (sccs) ******

****** LOADING (spell) ******

****** LOADING (tcpip) ******

****** LOADING (usat) ******

****** LOADING (usep) ******

You can recover some disk space by removing exercisers
for devices not configured on your system.

****** LOADING (userdev) ******

Unpacking files in /usr/src/userdev...

****** LOADING (uucp) ******

Command <help free rxunit rxdir list load unload exit>: exit


Make symbolic link for /usr/spool <y or n> ? n

****** ULTRIX-11 Setup Phase 2 Completed ******

The automated portion of the ULTRIX-11 software installation is
now complete. Return to the Installation Guide for instructions.


# 
----------------------------------------------------------------

We are now done installing stuff from the tape, so unload and
remove the tape in drive 0.

Then prepare for and perform the reboot:

---------------------------------------------------------------

        sync
        sync
        sync
        <reboot>

9 8 7 6 5 4 3 2 1 

DU0


Sizing Memory...  

Boot: rd(0,0)unix    (CTRL/C will abort auto-boot)

rd(0,0)unix: 37534+54720+8128+8000+7488+5312+3648

ULTRIX-11 Kernel V3.1

realmem = 524288
buffers = 76800
clists  = 2080
usermem = 285568
maxumem = 285568
erase = delete, kill = ^U, intr = ^C
#
---------------------------------------------------------

Looks good to me!  Move on to multi-user mode by logging
out of the shell (ctrl-d):

---------------------------------------------------------
Restricted rights:

        Use, duplication, or disclosure is subject
        to restrictions stated in your contract with
        Digital Equipment Corporation.

*UNIX is a trademark of AT&T Bell Laboratories.

Mounted /dev/rd06 on /usr

Sat Mar  7 22:57:00 GMT 1970

ERROR LOG has - 1 of 100 blocks used


ULTRIX-11 System V3.1 (kwek)

login: 
----------------------------------------------------------

Yay!  Log on as root and try some fun commands:

----------------------------------------------------------

Welcome to the ULTRIX-11 System

erase = delete, kill = ^U, intr = ^C
kwek#

kwek# uname -a
ULTRIX-11 kwek 3 0 PDP-11/53
kwek#

kwek# df
Filesystem    total    kbytes  kbytes  percent
   node       kbytes    used    free   used    Mounted on
/dev/rd00       4654    3201    1453    69%    /
/dev/rd06      13788   11461    2327    83%    /usr
kwek#

kwek# ps ax

   PID TTY TIME CMD
     0 ?   0:00 swapper
     1 ?   0:00 /etc/init
     2 ?   0:00 /etc/elc
    42 co  0:00 -sh 
    52 co  0:00 ps ax 
    34 ?   0:00 /etc/update
    38 ?   0:00 /etc/cron
kwek# 
------------------------------------------------------------

You're now all set.  Have fun with UNIX on your PDP-11 !

------------------------------------------------------------------------


Fred